? semiconductor components industries, llc, 2015 july, 2015 ? rev. 4 1 publication order number: mbrs230lt3/d mbrs230l, nrvbs230l surface mount schottky power rectifier smb power surface mount package this device employs the schottky barrier principle in a metal?to?silicon power rectifier. features epitaxial construction with oxide passivation and metal overlay contact. ideally suited for low voltage, high frequency switching power supplies; free wheeling diodes and polarity protection diodes. features ? compact package with j?bend leads ideal for automated handling ? highly stable oxide passivated junction ? guardring for over?voltage protection ? low forward voltage drop ? nrvbs prefix for automotive and other applications requiring unique site and control change requirements; aec?q101 qualified and ppap capable ? these devices are pb?free and are rohs compliant mechanical characteristics ? case: molded epoxy ? epoxy meets ul 94, v?0 @ 0.125 in. ? weight: 95 mg (approximately) ? finish: all external surfaces corrosion resistant and terminal leads are readily solderable ? maximum temperature of 260 c/10 seconds for soldering ? available in 12 mm tape, 2500 units per 13 reel, add ?t3? suffix to part number ? cathode polarity band www. onsemi.com smb case 403a schottky barrier rectifier 2.0 amperes 30 volts marking diagram device package shipping ? ordering information mbrs230lt3g smb (pb?free) 2500 / tape & ree l ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our t ape and reel packaging specification s brochure, brd8011/d. alyw 2bl3 a = assembly location l = wafer lot y = year w = work week = pb?free package NRVBS230LT3G smb (pb?free) 2500 / tape & ree l (note: microdot may be in either location)
mbrs230l, nrvbs230l www. onsemi.com 2 maximum ratings rating symbol value unit peak repetitive reverse voltage working peak reverse voltage dc blocking voltage v rrm v rwm v r 30 v average rectified forward current (at rated v r , t c = 110 c) i o 2.0 a peak repetitive forward current (at rated v r , square wave, 20 khz, t c = 105 c) i frm 4.0 a non?repetitive peak surge current (surge applied at rated load conditions, halfwave, single phase, 60 hz) i fsm 40 a storage/operating case temperature t stg , t c ?55 to +175 c operating junction temperature t j ?55 to +125 c voltage rate of change (rated v r , t j = 25 c) dv/dt 10,000 v/ s stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device function ality should not be assumed, damage may occur and reliability may be affected. thermal characteristics characteristic symbol value unit thermal resistance, junction?to?lead (note 1) thermal resistance, junction?to?ambient (note 1) r jl r ja 18.6 135 c/w electrical characteristics maximum instantaneous forward voltage (note 2) (i f = 2.0 a) see figure 2 (i f = 4.0 a) v f t j = 25 c t j = 125 c v 0.50 0.60 0.45 0.63 maximum instantaneous reverse current (note 2) (v r = 30 v) see figure 4 (v r = 15 v) i r t j = 25 c t j = 125 c ma 1 0.31 75 35 product parametric performance is indicated in the electrical characteristics for the listed test conditions, unless otherwise noted. product performance may not be indicated by the electrical characteristics if operated under different conditions. 1. minimum pad size (0.108 x 0.085 ) for each lead on fr4 board. 2. pulse test: pulse width 250 s, duty cycle 2.0%. figure 1. typical forward voltage figure 2. maximum forward voltage 0.6 0 v f , instantaneous forward voltage (volts) 10 1 0.01 0.1 0.4 v f , maximum instantaneous forward voltage (volts) 0.5 0.3 0.2 0.6 0 10 1 0.1 0.2 0.4 0.5 0.1 0.3 0.7 0. 8 0.1 i f , instantaneous forward current (amps) t j = 125 c 100 c 25 c ?55 c i f , instantaneous forward current (amps ) t j = 125 c 100 c 25 c
mbrs230l, nrvbs230l www. onsemi.com 3 figure 3. typical reverse current figure 4. maximum reverse current 30 0 v r , reverse voltage (volts) 100e?3 10e?3 10 15 20 3 0 0 v r , reverse voltage (volts) 100e?3 10e?3 1e?3 100e?6 10e?6 10 20 25 i r , reverse current (amps) 25 5 1e?3 100e?6 1e?6 10e?6 t j = 125 c t j = 100 c t j = 25 c t j = 125 c t j = 100 c t j = 25 c 515 i r , maximum reverse current (amps ) figure 5. current derating per leg figure 6. forward power dissipation per leg 40 80 20 t c , case temperature ( c) 2.0 1.0 0 i o , average forward current (amps) 0.5 2.0 0 1.8 1.2 1.0 0.4 0 60 140 120 1.0 1.5 0.6 3.0 freq = 20 khz 3.5 1.5 0.5 2.5 3. 5 2.5 3.0 0.2 0.8 1.4 dc 100 0 i o , average forward current (amps) square wave ipk/io = ipk/io = 5.0 ipk/io = 10 ipk/io = 20 1.6 p fo , average power dissipation (watts) t j = 125 c dc square wave ipk/io = ipk/io = 5.0 ipk/io = 10 ipk/io = 20 figure 7. thermal response 0.1 t, time (s) 1 0.1 0.01 0.001 0.0001 0.0001 0.001 0.01 1.0 10 100 100 0 r(t), transient thermal resistance (normalized) r j lead = 18.6 r j ambient = 150
mbrs230l, nrvbs230l www. onsemi.com 4 package dimensions smb case 403a?03 issue j e b d c l1 l a a1 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. dimension b shall be measured within dimension l1. 2.261 0.089 2.743 0.108 2.159 0.085 mm inches scale 8:1 *for additional information on our pb?free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* dim a min nom max min millimeters 1.95 2.30 2.47 0.077 inches a1 0.05 0.10 0.20 0.002 b 1.96 2.03 2.20 0.077 c 0.15 0.23 0.31 0.006 d 3.30 3.56 3.95 0.130 e 4.06 4.32 4.60 0.160 l 0.76 1.02 1.60 0.030 0.091 0.097 0.004 0.008 0.080 0.087 0.009 0.012 0.140 0.156 0.170 0.181 0.040 0.063 nom max 5.21 5.44 5.60 0.205 0.214 0.220 h e 0.51 ref 0.020 ref d l1 h e polarity indicator optional as needed p ublication ordering information n. american technical support : 800?282?9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81?3?5817?1050 mbrs230lt3/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303?675?2175 or 800?344?3860 toll free usa/canada fax : 303?675?2176 or 800?344?3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your loc al sales representative on semiconductor and the are registered trademarks of semiconductor components industries, llc (scillc) or its subsidia ries in the united states and/or other countries. scillc owns the rights to a number of pa tents, trademarks, copyrights, trade secret s, and other intellectual property. a listin g of scillc?s product/patent coverage may be accessed at www.onsemi.com/site/pdf/patent?marking.pdf. scillc reserves the right to make changes without further notice to any product s herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any part icular purpose, nor does sci llc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typi cal? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating param eters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the right s of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgic al implant into the body, or other applications intended to s upport or sustain life, or for any other application in which the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer s hall indemnify and hold scillc and its officers , employees, subsidiaries, affiliates, and dist ributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufac ture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner.
|
